# User/Group: This allows you to set the user and group that will be
# used for tinyproxy after the initial binding to the port has been done
# as the root user. Either the user or group name or the UID or GID
# number may be used.
User proxy
Group proxy

# Port: Specify the port which tinyproxy will listen on.  Please note
# that should you choose to run on a port lower than 1024 you will need
# to start tinyproxy using root.
Port 8888

# Timeout: The maximum number of seconds of inactivity a connection is
# allowed to have before it is closed by tinyproxy.
Timeout 600

# ErrorFile: Defines the HTML file to send when a given HTTP error
# occurs.  You will probably need to customize the location to your
# particular install.  The usual locations to check are:
#   /usr/local/share/tinyproxy
#   /usr/share/tinyproxy
#   /etc/tinyproxy
#
# ErrorFile 404 "/usr/share/tinyproxy/404.html"
# ErrorFile 400 "/usr/share/tinyproxy/400.html"
# ErrorFile 503 "/usr/share/tinyproxy/503.html"
# ErrorFile 403 "/usr/share/tinyproxy/403.html"
# ErrorFile 408 "/usr/share/tinyproxy/408.html"
#
# DefaultErrorFile: The HTML file that gets sent if there is no
# HTML file defined with an ErrorFile keyword for the HTTP error
# that has occured.
DefaultErrorFile "/usr/share/tinyproxy/default.html"

# Logfile: Allows you to specify the location where information should
# be logged to.  If you would prefer to log to syslog, then disable this
# and enable the Syslog directive.  These directives are mutually
# exclusive.
Logfile "/var/log/tinyproxy/tinyproxy.log"

# LogLevel: Set the logging level. Allowed settings are:
#       Critical        (least verbose)
#       Error
#       Warning
#       Notice
#       Connect         (to log connections without Info's noise)
#       Info            (most verbose)
#
# The LogLevel logs from the set level and above. For example, if the
# LogLevel was set to Warning, then all log messages from Warning to
# Critical would be output, but Notice and below would be suppressed.
LogLevel Connect

# PidFile: Write the PID of the main tinyproxy thread to this file so it
# can be used for signalling purposes.
PidFile "/var/run/tinyproxy/tinyproxy.pid"

# MaxClients: This is the absolute highest number of threads which will
# be created. In other words, only MaxClients number of clients can be
# connected at the same time.
#
MaxClients 1024

# MinSpareServers/MaxSpareServers: These settings set the upper and
# lower limit for the number of spare servers which should be available.
#
# If the number of spare servers falls below MinSpareServers then new
# server processes will be spawned.  If the number of servers exceeds
# MaxSpareServers then the extras will be killed off.
MinSpareServers 30
MaxSpareServers 60

# StartServers: The number of servers to start initially.
#
StartServers 30

# MaxRequestsPerChild: The number of connections a thread will handle
# before it is killed. In practise this should be set to 0, which
# disables thread reaping. If you do notice problems with memory
# leakage, then set this to something like 10000.
MaxRequestsPerChild 0

# ViaProxyName: The "Via" header is required by the HTTP RFC, but using
# the real host name is a security concern.  If the following directive
# is enabled, the string supplied will be used as the host name in the
# Via header; otherwise, the server's host name will be used.
ViaProxyName "tinyproxy"

# Filter: This allows you to specify the location of the filter file.
Filter "/etc/tinyproxy/filter"

# FilterURLs: Filter based on URLs rather than domains.
FilterURLs On

# FilterExtended: Use POSIX Extended regular expressions rather than
# basic.
FilterExtended On

# FilterDefaultDeny: Change the default policy of the filtering system.
# If this directive is commented out, or is set to "No" then the default
# policy is to allow everything which is not specifically denied by the
# filter file.
#
# However, by setting this directive to "Yes" the default policy becomes
# to deny everything which is _not_ specifically allowed by the filter
# file.
FilterDefaultDeny No

# ConnectPort: This is a list of ports allowed by tinyproxy when the
# CONNECT method is used.  To disable the CONNECT method altogether, set
# the value to 0.  If no ConnectPort line is found, all ports are
# allowed (which is not very secure.)
#
# The following two ports are used by SSL.
ConnectPort 443
ConnectPort 563